Hunter Cat NFC

electronicats · 1351

0 Usuarios y 1 Visitante están viendo este tema.

electronicats

  • Miembro
  • *
    • Mensajes: 9
    • Karma: +3/-0
    • Ver Perfil
on: Mayo 06, 2021, 01:42:10 pm
    https://electroniccats.com/store/hunter-cat-nfc/

    Understanding the Hunter Cat NFC and its LEDs
    The device has a preloaded reader detection firmware that lets the user know when he is near an NFC reader that is trying to read his card.

    Reader detection
     Detect hidden readers seeking to read your cards without authorization for cloning

    Turn on Hunter Cat NFC
    Wait for the LEDs to turn off
    Red LED flashes every 1 second
    Approach the reader, the huntercat NFC LEDs should light up indicating if an NFC reader was detected.
    If it does not turn on and the LED stays on, it is not near an NFC reader.

    HOW DOES IT WORK?
    Hunter Cat NFC can be set to behave either as an NFC reader a tag or to establish a two-way connection with another NFC device.  Hunter Cat NFC features a SAMD21 MCU which works in conjunction with the PN7150. The USB interface is provided by SAMD21 MCU, and the NFC functionality is ensured thanks to PN7150. NFC is designed to be intuitive for users. The Communication between two devices is established in the simplest way possible — by bringing them close to each other. NFC frontend can operate in three distinct modes:

    Card emulation mode — where HunterCat NFC behaves like a smart card or a tag
    In this mode, HunterCat NFC emulates a NFC tag. It doesn’t initiate the communication, it only responds to a NFC reader. A typical application of the card emulation mode is how people use NFC in their smartphones to replace several cards, badges or tags at once (using the same phone for RFID access controls, contactless payments and so on). Card emulation mode, however, is not useful just for smartphones, but for any type of portable device.



    Read/Write — where HunterCat NFC behaves as an NFC Reader/Writer
    Here, Hunter Cat communicates with a passive tag, NFC smart card, or an NFC device operating in card emulation mode. It can read or write to a tag (although reading is a more common use-case because tags will often be write protected). In this mode, the HunterCat NFC generates the RF field, while a tag or card only modulates it.



    Peer-to-peer — for more complex interactions
    Peer-to-peer mode establishes a two-way communication channel between a pair of NFC-enabled devices. When a user brings two devices close to each other, the two NFC chips establish a P2P connection and exchange data.


     

    For more information and updates on the working modes visit: https://github.com/ElectronicCats/HunterCatNFC

    Examples video:

    https://www.youtube.com/watch?v=W8bfdRUfckc


    https://www.youtube.com/watch?v=_y17rtbAfdA
     



     

    Characteristics:
    -Procesador Cortex M0+
    -USB C 2.0
    -NFC Reader, Card and NFC Forum
    -Arduino compatible
    -CircuitPython compatible
    -UF2 Bootloader
    -3 LEDs status
    -Open Hardware
    -Battery
    -RF protocols supported
    -NFCIP-1, NFCIP-2 protocol
    -ISO/IEC 14443A, ISO/IEC 14443B PICC, NFC Forum T4T modes via host interface
    -NFC Forum T3T via host interface
    -ISO/IEC 14443A, ISO/IEC 14443B PCD designed according to NFC Forum digital protocol T4T platform and ISO---DEP
    -eliCa PCD mode
    -MIFARE Classic PCD encryption mechanism (MIFARE Classic 1K/4K)
    -NFC Forum tag 1 to 5 (MIFARE Ultralight, Jewel, Open FeliCa tag, MIFAREDESFire
    -ISO/IEC 15693/ICODE VCD mode
    -Includes NXP ISO/IEC14443-A and Innovatron ISO/IEC14443-B intellectual property licensing rights[/li][/list]


    https://electroniccats.com/store/hunter-cat-nfc/
    « Última Modificación: Mayo 06, 2021, 01:43:53 pm por electronicats »